What are the voltage ratings of Coaxial Cable Assemblies

Coaxial cable assemblies are critical components in signal transmission systems, used in industries ranging from consumer electronics to aerospace. The voltage rating of a coaxial cable assembly refers to the maximum voltage it can safely handle over a specified period without dielectric breakdown, insulation failure, or performance degradation. This rating directly impacts system safety, reliability, and lifespan—ignoring it can lead to short circuits, equipment damage, or even safety hazards like electric arcs.

1. Key Definitions: AC vs. DC Voltage Ratings

Voltage ratings for coaxial cable assemblies are typically specified for two types of voltage, and confusing them can cause critical errors:

DC Voltage Rating: Applies to direct current systems (e.g., power supplies). It reflects the cable’s ability to resist dielectric breakdown under steady voltage. DC ratings are usually higher than AC ratings for the same cable, as DC lacks the “peak voltage” fluctuations of AC.
AC Voltage Rating: For alternating current systems (e.g., RF signals, industrial power). It is often specified as RMS (Root Mean Square) voltage, not peak voltage. For example, a cable rated for 600V AC RMS may have a peak voltage of ~848V (600V × √2)—engineers must account for this to avoid overloading.

2. Factors That Determine Voltage Ratings

The voltage rating of a coaxial cable assembly is not arbitrary; it depends on four core factors:

a. Dielectric (Insulation) Material

The dielectric layer (between the inner conductor and outer shield) is the primary barrier against voltage breakdown. Common materials and their typical voltage capabilities include:

PTFE (Polytetrafluoroethylene): High-temperature resistance (up to 260°C) and excellent dielectric strength (~20–30 kV/mm). Used in high-voltage, high-frequency applications (e.g., aerospace, medical equipment) with ratings often exceeding 1,000V.
PE (Polyethylene): Cost-effective, low dielectric loss, but limited to lower temperatures (up to 80°C). Suitable for consumer electronics (e.g., TV antennas) with ratings between 50V and 300V.
FEP (Fluorinated Ethylene Propylene): Balances PTFE’s performance and PE’s processability, with voltage ratings of 300V–1,500V for industrial sensors or telecom equipment.

b. Operating Temperature

Voltage ratings decrease as temperature rises. Most manufacturers specify ratings at 25°C (room temperature); for every 10°C increase beyond this, the rating may drop by 5–10%. For example, a cable rated 600V at 25°C might only handle 450V at 85°C. This is critical for high-temperature environments like automotive engine bays or industrial ovens.

c. Cable Design & Construction

Conductor Size: Larger inner conductors reduce current density, minimizing heat buildup that can weaken insulation. A 14 AWG (American Wire Gauge) conductor will support a higher voltage rating than a 22 AWG conductor of the same dielectric material.
Shielding: Proper shielding (e.g., braided, foil) prevents external electromagnetic interference (EMI) from disrupting the dielectric’s integrity. Poor shielding can indirectly lower effective voltage tolerance by causing signal distortion or insulation stress.

d. Environmental Conditions

Moisture, chemicals, or mechanical stress can degrade insulation over time, reducing voltage ratings. For example, a cable rated 1,000V in dry environments may only handle 600V in humid or corrosive settings (e.g., marine applications).

3. Common Voltage Rating Ranges by Application

Voltage ratings are tailored to specific use cases. Below are typical ranges:

Application	Voltage Rating Range	Example Use Cases
Consumer Electronics	50V – 300V (AC/DC)	TV cables, Wi-Fi routers, audio systems
Industrial Automation	300V – 2,000V (AC/DC)	Sensor cables, PLC connections, motor controls
RF & Telecommunications	500V – 3,000V (AC)	Cellular base stations, satellite dishes, radar systems
High-Voltage Specialized	3,000V – 30,000V (DC)	Medical imaging (MRI), test equipment, power distribution

4. Practical Guidelines for Selecting the Right Voltage Rating

To avoid system failures, follow these steps when choosing a coaxial cable assembly:

Identify the maximum voltage in your system: Include transient spikes (e.g., power surges) – select a rating 20–30% higher than the peak voltage to add a safety margin.
Account for operating temperature: If the cable will be exposed to temperatures above 25°C, check the manufacturer’s “temperature derating curve” to adjust the rating.
Verify compliance with standards: Ensure the cable meets industry standards (e.g., UL 910 for plenum cables, IEC 61196 for RF cables) to guarantee safety and performance.
Consider environmental factors: For wet, corrosive, or high-vibration environments, choose cables with reinforced insulation (e.g., PTFE with a protective jacket).

5. Common Misconceptions to Avoid

Myth 1: “Higher voltage ratings are always better.” Over-specifying (e.g., using a 5,000V cable for a 100V TV) increases cost and may reduce flexibility, making installation harder.
Myth 2: “AC and DC ratings are interchangeable.” A cable rated 600V AC may only handle 400V DC, as AC’s peak voltage imposes greater stress on insulation.
Myth 3: “Voltage rating is the only factor.” Signal frequency, impedance (e.g., 50Ω, 75Ω), and current capacity also matter—always match all parameters to your application.

Conclusion

Understanding the voltage ratings of coaxial cable assemblies is essential for building safe, reliable systems. By considering dielectric materials, temperature, application needs, and safety margins, you can avoid costly failures.

For businesses and engineers seeking high-quality coaxial cable assemblies tailored to specific voltage requirements, FRS brand factory stands out as a trusted partner. FRS specializes in customizing coaxial cable assemblies with voltage ratings from 50V to 30,000V, using premium dielectrics (PTFE, FEP, PE) and complying with global standards (UL, IEC, RoHS). Whether for consumer electronics, industrial automation, or high-voltage medical equipment, FRS ensures each assembly meets your exact voltage and performance needs—delivering durability and peace of mind for every application.

What are the voltage ratings of Coaxial Cable Assemblies - Micro Coaxial Cable factory-(FRS)

INFO

1. Key Definitions: AC vs. DC Voltage Ratings

2. Factors That Determine Voltage Ratings

a. Dielectric (Insulation) Material

b. Operating Temperature

c. Cable Design & Construction

d. Environmental Conditions

3. Common Voltage Rating Ranges by Application

4. Practical Guidelines for Selecting the Right Voltage Rating

5. Common Misconceptions to Avoid

Conclusion

TAGS

FAQ

NEWS

More Products

Flexible Micro-Coaxial Assemblies

I-PEX Micro Coaxial Cable

Contact Us

Call Us

Email Us